Register Now

**speckman37** · 02-20-2020, 12:34 PM

I purchased a 2020 F350 - it has a 3" bumper hitch connection. Currently i have a sleeve that takes it down to a 2". I am looking for a 3" shaft that has a 2" ball. The way I am set up now the bouncing is violent. I found one made by B&W this morning. Any recommendations are appreciated.

**DCW** · 02-20-2020, 12:47 PM

I got mine at walmart

**bwguardian** · 02-20-2020, 01:35 PM

Quote:

Originally Posted by speckman37

I purchased a 2020 F350 - it has a 3" bumper hitch connection. Currently i have a sleeve that takes it down to a 2". I am looking for a 3" shaft that has a 2" ball. The way I am set up now the bouncing is violent. I found one made by B&W this morning. Any recommendations are appreciated.

Something is not set up right if you are "bouncing violently", sounds like too much tongue weight. It would be helpful to know your location as I have had good luck with Husky Trailer Parts on the south side of Houston.

**tmd11111** · 02-20-2020, 06:36 PM

I have a '20 Super Duty as well. Was surprised that it came with a 3" receiver and a 2.5" adapter. I already have a half dozen 2" bars and didn't feel like buying another. Found a 2,5" to 2" sleeve at Walmart for around $10. Just put a layer of duct tape on each adapter then pounded them in place. Already have about 500 miles towing my boat and no rattle.

**Helislug** · 02-22-2020, 07:17 AM

this might help:

https://www.amazon.com/dp/B001EOWR3Y...v_ov_lig_dp_it

**68rustbucket** · 02-22-2020, 06:33 PM

I have the 3” on my 2019. And am using 2 sleeves to use my solid draw bar. The rattling is annoying.

**hurricane matt** · 02-27-2020, 12:37 PM

Check your hitch pin lock to make sure it fits. Swapped hitches for a bit with someone else and had to get a different one because theirs had a different diameter, and too much play.

Sent from my Pixel 3 using Tapatalk

02-20-2020, 12:34 PM	#1
speckman37 Registered Users-pm+ Join Date: Jun 26 2008 Age: 53 Posts: 19 Rep Power: 0	3" Bumper pull hitch recommendation needed I purchased a 2020 F350 - it has a 3" bumper hitch connection. Currently i have a sleeve that takes it down to a 2". I am looking for a 3" shaft that has a 2" ball. The way I am set up now the bouncing is violent. I found one made by B&W this morning. Any recommendations are appreciated.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

02-20-2020, 12:47 PM	#2
DCW Registered Users-pm+ Join Date: Aug 02 2005 Location: Junction, Tx Age: 67 Posts: 942 Rep Power: 2017167	I got mine at walmart

02-20-2020, 06:36 PM	#4
tmd11111 Registered Users-pm+ Join Date: Mar 25 2019 Location: San Angelo,TX Posts: 100 Rep Power: 449379	I have a '20 Super Duty as well. Was surprised that it came with a 3" receiver and a 2.5" adapter. I already have a half dozen 2" bars and didn't feel like buying another. Found a 2,5" to 2" sleeve at Walmart for around $10. Just put a layer of duct tape on each adapter then pounded them in place. Already have about 500 miles towing my boat and no rattle.

02-22-2020, 07:17 AM	#5
Helislug Registered Users-pm+ Join Date: Feb 20 2018 Posts: 23 Rep Power: 0	this might help: https://www.amazon.com/dp/B001EOWR3Y...v_ov_lig_dp_it

02-22-2020, 06:33 PM	#6
68rustbucket Registered Users-pm+ Join Date: Dec 03 2009 Posts: 51 Rep Power: 4158	I have the 3” on my 2019. And am using 2 sleeves to use my solid draw bar. The rattling is annoying.

02-27-2020, 12:37 PM	#7
hurricane matt Registered Users-pm+ Join Date: Apr 11 2017 Posts: 2,311 Rep Power: 16719841	Check your hitch pin lock to make sure it fits. Swapped hitches for a bit with someone else and had to get a different one because theirs had a different diameter, and too much play. Sent from my Pixel 3 using Tapatalk

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)

vBulletin Message

Cancel Changes

Register Now

Log-in